Recalibrating Technical Education: Student Skill Readiness and Industry Alignment in the Machine Shop Technology Program of Cebu Technological University Using Module Output
DOI:
https://doi.org/10.5281/zenodo.24286339Keywords:
competency-based education, machine shop technology, industry alignment, skill readiness, instructional module, TESDAAbstract
This study examined the alignment between the competencies acquired by Bachelor of Industrial Technology major in Machine Shop Technology students at Cebu Technological University – Main Campus and the skills required by machine shop industries in Cebu City during the Academic Year 2024–2025, as basis for an enhanced instructional module. Using a descriptive-quantitative design, data were gathered from 31 respondents (18 third-year students, 9 fourth-year students, and 4 OJT supervisors) through a structured competency checklist based on TESDA Training Regulations for Machining NC I and NC II. The instrument measured school-based performance and OJT supervisors' assessments using a 3-point Likert scale (3 – Fully Acquired, 2 – Acquired, 1 – Not Acquired). Descriptive statistics (weighted mean, cross-tabulation) and a t-test for independent samples were employed. Findings revealed that students demonstrated "Fully Acquired" competencies in benchwork (2.54), lathe work (2.50), and drilling work (2.52), while milling work (2.46) was described as "Acquired." OJT supervisors rated student proficiency as "Acquired" across all areas—benchwork (2.48), lathe work (2.44), milling work (2.41), and drilling work (2.48)—and expressed strong overall approval of student work readiness and program alignment (2.55, "Fully Agree"). The t-test results revealed no significant difference (p > 0.05) between student self-assessments and supervisor assessments in any competency area, indicating that students have realistic self-perceptions and that school-based training aligns with industry expectations. Relatively lower ratings in precision-oriented skills—technical drawing interpretation, taper turning, threading, speed/feed calculations, keyway cutting, milling cutter selection, reaming, and blind hole drilling—were identified as areas for enhancement. The study concludes that the Machine Shop Technology program effectively prepares students with the skills demanded by the machine shop sector. It recommends the implementation of an enhanced competency-based learning module featuring TESDA-aligned outcomes, industry-simulated performance tasks, scaffolded activities, integrated computation exercises, enhanced drawing interpretation, authentic assessment tools, and industry feedback integration, supported by faculty development, facility enhancement, and strengthened industry partnerships.
Downloads
References
Beduya, L. A., Santos, R. M., & Villanueva, J. C. (2021). Technical education and industry readiness: Assessing the machine shop programs in Philippine state universities. Journal of Technical Education and Training, 13(4), 45–62.
Commission on Higher Education (CHED). (2017). CHED Memorandum Order (CMO) No. 86, Series of 2017: Policies, standards and guidelines for Bachelor of Science in Mechanical Engineering (BSME) and Bachelor of Science in Manufacturing Engineering (BSMfgE). Quezon City: Commission on Higher Education.
Commission on Higher Education (CHED). (2020). Handbook on typology, outcomes-based education, and institutional sustainability assessment. Quezon City: CHED.
Cuasito, R. D., Fernandez, M. T., & Lim, P. K. (2023). The state of manufacturing technology adoption in Cebu's machine shop industry: Challenges in the age of Industry 4.0. Philippine Journal of Industrial Engineering and Technology, 8(2), 112–128.
International Labour Organization (ILO). (2022). Competency-based training and assessment: Global best practices in technical and vocational education. Geneva: International Labour Office.
Philippine Institute for Development Studies (PIDS). (2023). Skills mismatch in the Philippine manufacturing sector: Causes, consequences, and policy recommendations (Discussion Paper Series No. 2023-15). Makati: PIDS.
Piaget, J. (1972). The psychology of the child. New York: Basic Books.
Prasteyo, A. B., Cruz, M. D., & Reyes, J. T. (2023). Technological lag and workforce development: A study of traditional machine shops in regional manufacturing hubs. Asian Journal of Technology and Innovation, 31(4), 234–251.
Technical Education and Skills Development Authority (TESDA). (2023). Competency-based curriculum development guide for the metals and engineering sector. Taguig: TESDA Planning Office.
Technical Education and Skills Development Authority (TESDA). (2024). Training regulations for Machining NC I and NC II. Taguig: TESDA Publications.
Technical Education and Skills Development Authority (TESDA). (2024). Trainer's Methodology Level I (TM I) competency standards. Taguig: TESDA Qualifications and Standards Office.
Vygotsky, L. S. (1978). Mind in society: The development of higher psychological processes. Cambridge: Harvard University Press.
Downloads
Published
Issue
Section
License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.